Page 2 of 2 FirstFirst 12
Results 61 to 85 of 85

Thread: Build and Restoration: 1994 S124 w/ 600hp OM606, 5-speed standard trans

  1. #61

    Re: Build and Restoration: 1994 S124 w/ 600hp OM606, 5-speed standard trans

    Quote Originally Posted by S70/2 View Post
    They are 18" with 225/45s up front, with the lorinser springs the rubbing was not great even with heavily rolled fenders. The H&Rs are much more reasonable and work nicely. The oil supply fitting is a 16mm to 4AN, straight thread 16mm with a copper washer. The om606 oil feed boss is large and flat perfect for a crush washer.

    The super wagon has been running and driving great, just rolled over 1200 miles so the "new car break in" is done. The methanol injection with Snow 50/50 boost juice made a very noticeable increase in power. Will be headed off to the body shop in the very near future for its 036 Widebody transformation, then meatier tires and more boost
    Did you use v8 4 bolt flex discs? I need to go back through the thread.

    The outer axle shafts apparently fail at the splines with serious tires. I am looking for a usable factory hub with larger splines to have some custom half shafts made with the larger knuckle and splines on both ends.

    Sent from my SAMSUNG-SM-G935A using Tapatalk

  2. #62

    Re: Build and Restoration: 1994 S124 w/ 600hp OM606, 5-speed standard trans

    Quote Originally Posted by atg View Post
    Did you use v8 4 bolt flex discs? I need to go back through the thread.

    The outer axle shafts apparently fail at the splines with serious tires. I am looking for a usable factory hub with larger splines to have some custom half shafts made with the larger knuckle and splines on both ends.

    Sent from my SAMSUNG-SM-G935A using Tapatalk
    And thanks very much for the information.

    Sent from my SAMSUNG-SM-G935A using Tapatalk

  3. #63
    .036 Hoonigan™
    E500E Boffin
    gsxr's Avatar
    Join Date
    Dec 2008
    Location
    Boise, ID, USA
    Posts
    20,583

    Re: Build and Restoration: 1994 S124 w/ 600hp OM606, 5-speed standard trans

    Quote Originally Posted by atg View Post
    The outer axle shafts apparently fail at the splines with serious tires. I am looking for a usable factory hub with larger splines to have some custom half shafts made with the larger knuckle and splines on both ends.
    How serious do the tires have to be to cause the spline failure? Are we talking Pilot street tires on the street, or Hoosier drag radials at the track with VHT?

    Also, does the failure tend to be at initial launch (zero mph), or at speed at the power peak during a shift, etc?


  4. #64

    Re: Build and Restoration: 1994 S124 w/ 600hp OM606, 5-speed standard trans

    Quote Originally Posted by gsxr View Post
    How serious do the tires have to be to cause the spline failure? Are we talking Pilot street tires on the street, or Hoosier drag radials at the track with VHT?

    Also, does the failure tend to be at initial launch (zero mph), or at speed at the power peak during a shift, etc?

    Serious enough to provide any traction before 3rd gear at 60mph. Which practically speaking means Hoosier drag radials, like a 265 rear.

    Sent from my SAMSUNG-SM-G935A using Tapatalk

  5. The Following User Says Thank You to atg For This Useful Post:

    gsxr (03-15-2018)

  6. #65

    Re: Build and Restoration: 1994 S124 w/ 600hp OM606, 5-speed standard trans

    Quote Originally Posted by atg View Post
    Serious enough to provide any traction before 3rd gear at 60mph. Which practically speaking means Hoosier drag radials, like a 265 rear.

    Sent from my SAMSUNG-SM-G935A using Tapatalk
    Although I believe they have failed on street cars also.

    Sent from my SAMSUNG-SM-G935A using Tapatalk

  7. #66

    Re: Build and Restoration: 1994 S124 w/ 600hp OM606, 5-speed standard trans

    Quote Originally Posted by atg View Post
    Although I believe they have failed on street cars also.

    Sent from my SAMSUNG-SM-G935A using Tapatalk
    That dude in Norway had one fail in 3rd gear during a pull with street tires.

    Sent from my SAMSUNG-SM-G935A using Tapatalk

  8. The Following User Says Thank You to atg For This Useful Post:

    gsxr (03-15-2018)

  9. #67

    Post Re: Build and Restoration: 1994 S124 w/ 600hp OM606, 5-speed standard trans

    Got the vented 036 fender back from the custom metal shop, looking very good


    DB13BB07-3E68-4C6F-B97C-77948661559F.jpeg

    A bit wider than stock
    B32ACEF4-7CA7-4031-92EE-26539C3A2F31.jpeg


    0DBA1CD0-B210-4C38-B7F7-95913CEA90B8.jpeg

    749BAFDE-B18A-4D22-8A67-9AD9EDEF23A9.jpeg

    6B341FBE-EDE4-4616-A7E4-24A4EADA6173.jpeg

    E59462CE-9B57-4F95-B74E-E87CB5C50F81.jpeg


    Also got the full 3" stainless exhaust finished, complete with electric cutout

    4226D561-DABA-402D-9BE0-3AF3E3C83651.jpeg

    2420D00D-829A-45BC-9B04-68FA5BA0E14E.jpeg


    It is going in for the rear 1/4 panels this week then finally off to the bodyshop, who will have their hands full making everything just right with all these trash angel 036 parts

  10. The Following 5 Users Say Thank You to S70/2 For This Useful Post:

    600Eric (04-27-2018), a777fan (04-24-2018), gsxr (04-25-2018), maw1124 (05-02-2018), sheward (04-26-2018)

  11. #68

    Re: Build and Restoration: 1994 S124 w/ 600hp OM606, 5-speed standard trans

    Quote Originally Posted by S70/2 View Post
    Got the vented 036 fender back from the custom metal shop, looking very good


    It is going in for the rear 1/4 panels this week then finally off to the bodyshop, who will have their hands full making everything just right with all these trash angel 036 parts
    Where do you buy your sanitary tubing? Regular rolled 300d fenders work fine; mine rubs only on the liner right front on deep compression.

    Sent from my SAMSUNG-SM-G935A using Tapatalk

  12. #69
    .036 Hoonigan™
    E500E Boffin
    gsxr's Avatar
    Join Date
    Dec 2008
    Location
    Boise, ID, USA
    Posts
    20,583

    Re: Build and Restoration: 1994 S124 w/ 600hp OM606, 5-speed standard trans

    Quote Originally Posted by atg View Post
    Regular rolled 300d fenders work fine; mine rubs only on the liner right front on deep compression.
    Standard fenders may clear most larger wheels, but they are not widebody, and also have a different shape on the wheel arch. Blair is installing a complete 500E front end, plus 500E rear flared fenders too... complete widebody treatment.


  13. The Following User Says Thank You to gsxr For This Useful Post:

    atg (04-25-2018)

  14. #70

    Re: Build and Restoration: 1994 S124 w/ 600hp OM606, 5-speed standard trans

    Quote Originally Posted by gsxr View Post
    Standard fenders may clear most larger wheels, but they are not widebody, and also have a different shape on the wheel arch. Blair is installing a complete 500E front end, plus 500E rear flared fenders too... complete widebody treatment.

    Oh I see. I recall Russell doing something similar in seattle but I am wondering if doing so would actually solve any problems or is just to win the parking lot wars.

    Sent from my SAMSUNG-SM-G935A using Tapatalk

  15. #71
    .036 Hoonigan™
    E500E Boffin
    gsxr's Avatar
    Join Date
    Dec 2008
    Location
    Boise, ID, USA
    Posts
    20,583

    Re: Build and Restoration: 1994 S124 w/ 600hp OM606, 5-speed standard trans

    Quote Originally Posted by atg View Post
    Oh I see. I recall Russell doing something similar in seattle but I am wondering if doing so would actually solve any problems or is just to win the parking lot wars.
    It allows fitting MUCH wider wheels/tires in the rear, and moderately wider up front. And IMO, it looks soooo much better than non-widebody, but as always looks are in the eye of the beer holder...


  16. #72

    Re: Build and Restoration: 1994 S124 w/ 600hp OM606, 5-speed standard trans

    Ok so what size tire do you figure fits the rear on an 036 that wont fit an e420?

    And are the inner fender liners on the front really that different?

    Im not sure the front fender flare on the 036 is any bigger than what rolling a stock fender can produce. Seems like there are some body spacers involved, but those could be added to stock fenders, could they not?

    I guess without knowing what the goals are it is hard to say what sort of effort is justified.



    Sent from my SAMSUNG-SM-G935A using Tapatalk

  17. #73

    Re: Build and Restoration: 1994 S124 w/ 600hp OM606, 5-speed standard trans

    The stock fenders were rolled as much as possible, even to the point of deforming the arch with so much pull. No way you could get anywhere near 036 fender clearance. There’s enough room to have dinner in the wheel wells now, should be able to fit a 20-30mm wider tire without issue.

    Just the awesome look alone is worth the effort, at least in a super wagon such as this

  18. The Following 2 Users Say Thank You to S70/2 For This Useful Post:

    gsxr (04-26-2018), sheward (04-26-2018)

  19. #74
    .036 Hoonigan™
    E500E Boffin
    gsxr's Avatar
    Join Date
    Dec 2008
    Location
    Boise, ID, USA
    Posts
    20,583

    Re: Build and Restoration: 1994 S124 w/ 600hp OM606, 5-speed standard trans

    Quote Originally Posted by atg View Post
    Ok so what size tire do you figure fits the rear on an 036 that wont fit an e420? And are the inner fender liners on the front really that different?

    Im not sure the front fender flare on the 036 is any bigger than what rolling a stock fender can produce. Seems like there are some body spacers involved, but those could be added to stock fenders, could they not?

    I guess without knowing what the goals are it is hard to say what sort of effort is justified.
    On a standard 124, pretty much the reasonable limit is an 8.5" wheel on all four corners, with significant fender massaging & spacers required (AMG doc here). Note AMG also specs a travel-limiting strut shaft spacer up front as well to avoid rubbing under compression. Also, AMG specs a 235 tire, and a 245 is probably the max that would work, with a higher numerical offset wheel. At the risk of pissing off a lot of people, I'm going on record that I don't consider stretching a 205-section tire over a 9+ inch wheel as "fitting" on the car.

    So, on the E500E, bone stock it can fit 10.5" wheels in the rear with 285 tires, and 9.0 up front with 255 tires. This assumes the correct offset, of course. Zero rubbing, zero modifications. Some people have gone even wider.

    The 036 fender flares are MUCH bigger than what you can get by rolling stock 124 fenders.


  20. The Following 3 Users Say Thank You to gsxr For This Useful Post:

    a777fan (04-26-2018), atg (04-26-2018), ccrelan (04-26-2018)

  21. #75

    Re: Build and Restoration: 1994 S124 w/ 600hp OM606, 5-speed standard trans

    Ok maybe I will make a plan to put them on. I have to repaint my fenders anyway, so might as well paint bigger ones. Will keep an eye on the web for a carcass.

  22. #76

    Re: Build and Restoration: 1994 S124 w/ 600hp OM606, 5-speed standard trans

    That ought to be an exciting ride when it's done!
    Tom Hanson
    Parts Manager, Mercedes-Benz Classic Center, USA
    MBUSA, LLC
    949 598-4842 direct
    thomas.hanson@mbusa.com

  23. #77

    Re: Build and Restoration: 1994 S124 w/ 600hp OM606, 5-speed standard trans

    Electric cutout demonstration, for the prius enthusiasts


  24. The Following User Says Thank You to S70/2 For This Useful Post:

    gsxr (05-02-2018)

  25. #78

    Re: Build and Restoration: 1994 S124 w/ 600hp OM606, 5-speed standard trans

    Quote Originally Posted by S70/2 View Post
    Electric cutout demonstration, for the prius enthusiasts
    Did you swap the radiator support also? Thanks.

    Sent from my SAMSUNG-SM-G935A using Tapatalk

  26. #79

    Re: Build and Restoration: 1994 S124 w/ 600hp OM606, 5-speed standard trans

    Quote Originally Posted by atg View Post
    Did you swap the radiator support also? Thanks.

    Sent from my SAMSUNG-SM-G935A using Tapatalk
    I must be missing something, why would I swap the radiator support?

  27. #80
    .036 Hoonigan™
    E500E Boffin
    gsxr's Avatar
    Join Date
    Dec 2008
    Location
    Boise, ID, USA
    Posts
    20,583

    Re: Build and Restoration: 1994 S124 w/ 600hp OM606, 5-speed standard trans

    Quote Originally Posted by S70/2 View Post
    I must be missing something, why would I swap the radiator support?
    I'm guessing he means the lower radiator support, which is totally different on the .036 chassis.


  28. #81

    Re: Build and Restoration: 1994 S124 w/ 600hp OM606, 5-speed standard trans

    Quote Originally Posted by S70/2 View Post
    I must be missing something, why would I swap the radiator support?
    I have never seen a 500e, so it is all a bit mysterious. Above, someone said you were swapping the whole front end, but I'm not sure what that includes, to wit:

    "Blair is installing a complete 500E front end, plus 500E rear flared fenders too... complete widebody treatment."

    Sent from my SAMSUNG-SM-G935A using Tapatalk

  29. #82
    .036 Hoonigan™
    E500E Boffin
    gsxr's Avatar
    Join Date
    Dec 2008
    Location
    Boise, ID, USA
    Posts
    20,583

    Re: Build and Restoration: 1994 S124 w/ 600hp OM606, 5-speed standard trans

    Ah - got it. Generally speaking, the front-end swap consists of bolt-on parts: bumpers, fenders, fender liners, etc.

    The lower radiator support is welded to the chassis and would require considerably more effort to swap. IIRC, the piece may be NLA new (not sure). The advantage is twofold: First, it is much stronger; and second it does not have the two forward braces which take up space needed for either intercoolers (diesel applications) or engine oil cooler (036).


  30. #83
    Senior Member baviking1's Avatar
    Join Date
    Apr 2013
    Posts
    483

    Re: Build and Restoration: 1994 S124 w/ 600hp OM606, 5-speed standard trans

    Quick update; The Wagon goes in to the custom rod shop in the next two weeks for the 500E rear flare widebody addition. I have been utterly buried with health issues & the building of my animal rescue etc et al, and am looking forward to its completion. Updates & dyno runs will be forthcoming (as well as the long-delayed 500E partout), so stay tuned to witness the unmitigated genius of UberKarl. This car can literally tie your stomach in knots (and the diesel plumes can blot out the sun........

  31. The Following 7 Users Say Thank You to baviking1 For This Useful Post:

    ace10 (3 Days Ago), ccrelan (3 Days Ago), gsxr (2 Days Ago), Hakie (3 Days Ago), JC220 (3 Days Ago), S70/2 (2 Days Ago), TerryA (8 Hours Ago)

  32. #84

    Re: Build and Restoration: 1994 S124 w/ 600hp OM606, 5-speed standard trans

    Quote Originally Posted by baviking1 View Post
    Quick update; The Wagon goes in to the custom rod shop in the next two weeks for the 500E rear flare widebody addition. I have been utterly buried with health issues & the building of my animal rescue etc et al, and am looking forward to its completion. Updates & dyno runs will be forthcoming (as well as the long-delayed 500E partout), so stay tuned to witness the unmitigated genius of UberKarl. This car can literally tie your stomach in knots (and the diesel plumes can blot out the sun........
    Are you the owner or the builder?

    Sent from my SM-G955U using Tapatalk

  33. #85

    Re: Build and Restoration: 1994 S124 w/ 600hp OM606, 5-speed standard trans

    Quote Originally Posted by atg View Post
    Are you the owner or the builder?

    Sent from my SM-G955U using Tapatalk
    Baviking1 = Owner

    S70/2 = Builder

    GSXR = Deity

Similar Threads

  1. Bad speed (lack of power, low top speed)
    By Mercedes only in forum Electrical, CAN and Wiring
    Replies: 20
    Last Post: 12-28-2016, 12:24 AM
  2. Replies: 14
    Last Post: 01-13-2016, 09:49 AM
  3. 1994 E420 w/asr - cleaning the Speed sensors
    By E320A in forum 400E / E420 Discussions
    Replies: 0
    Last Post: 02-06-2013, 07:57 PM
  4. Car Restoration Company
    By 500ESpain in forum Off-Topic Discussions
    Replies: 1
    Last Post: 01-27-2010, 07:52 AM
  5. Leather restoration
    By 500ESpain in forum Interior Topics
    Replies: 4
    Last Post: 12-04-2009, 02:29 AM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •